Search found 1377 matches

by Patricks Dad
Fri Aug 16, 2019 6:44 am
Forum: Boat-Building Tips & Techniques
Topic: Notches in all the station molds at the baseline?
Replies: 13
Views: 560

Re: Notches in all the station molds at the baseline?

Yes Jim, I agree. that's a good tip!
by Patricks Dad
Thu Aug 15, 2019 5:07 pm
Forum: Boat-Building Tips & Techniques
Topic: Notches in all the station molds at the baseline?
Replies: 13
Views: 560

Re: Notches in all the station molds at the baseline?

I've mulled this a bit more and I'm guessing that those baseline notches are to mark the actual baseline. If you build your forms taller (some people want their build to be a bit higher for convenience - I always add a couple inches to my molds if my plywood allows the molds to still fit on 2 sheets...
by Patricks Dad
Thu Aug 15, 2019 1:46 pm
Forum: Boat-Building Tips & Techniques
Topic: Notches in all the station molds at the baseline?
Replies: 13
Views: 560

Re: Notches in all the station molds at the baseline?

Jim, I'm not so sure you / we are interpreting the question.... the question references 2 notches in each form (not one in the middle)...

"I notice that there are two notches in all the molds at the baseline."
by Patricks Dad
Thu Aug 15, 2019 8:42 am
Forum: Boat-Building Tips & Techniques
Topic: Notches in all the station molds at the baseline?
Replies: 13
Views: 560

Re: Notches in all the station molds at the baseline?

I've built the Redbird but I don't remember the notches you are referring to. A picture would help. I would advise that you extend your forms an inch below the sheerline on a fair curve to give yourself some additional material to use for clamping (and I always put a notch at the sheerline to make s...
by Patricks Dad
Tue Jul 02, 2019 8:54 pm
Forum: Paddling Events & "Get Togethers"
Topic: Rendezvous Sept 14,15 2019!
Replies: 2
Views: 428

Rendezvous Sept 14,15 2019!

Who's going to the Bear Mountain Boat Makers Rendezvous? I'm going to make the long trek and then spend a few days paddling in Algonquin.


https://www.bearmountainboats.com/pages ... zvous-2019

You know you want to go!
by Patricks Dad
Mon Jun 24, 2019 9:12 pm
Forum: Builders' Forum
Topic: Hull Repair
Replies: 41
Views: 2127

Re: Hull Repair

Brian is correct. Your image link needs to be a link to the image itself. If you click on the links in your post above, you don't get to the image, you get to a page that contains the image. From there, click on the image itself (which will show a page with just the image) and then you can right cli...
by Patricks Dad
Sun Jun 23, 2019 7:04 pm
Forum: Builders' Forum
Topic: Hull Repair
Replies: 41
Views: 2127

Re: Hull Repair

none of your pictures show up (and the links don't take you to pictures) It really isn't hard. Just click the [ img][ /img] button (9th button from the left) at the top of your window and the insert your link to the picture there between the img and /img (add no spaces) to any of the html code. The ...
by Patricks Dad
Mon Jun 17, 2019 12:34 pm
Forum: Builders' Forum
Topic: Finished!
Replies: 8
Views: 648

Re: Finished!

Excellent work!
by Patricks Dad
Fri Jun 14, 2019 8:26 am
Forum: Builders' Forum
Topic: Hull Repair
Replies: 41
Views: 2127

Re: Hull Repair

If you click on the links you have included an image will come up but it is part of a larger web page.... click on the image and then right click on that picture to capture a link to just the picture itself. Insert that link into the [gmi]xxx[/gmi] construct (but reverse the letters - 'img' instead ...
by Patricks Dad
Fri May 31, 2019 12:23 pm
Forum: Builders' Forum
Topic: Installing Outwales
Replies: 18
Views: 1249

Re: Installing Outwales

You won't need to thin the first coat as much as Epifanes suggests because you aren't worried about deep penetration into the wood. If you were (or places where you are) varnishing bare wood, that level of thinning makes sense. I generally thin about 10-20% for all coats. I've never been able to app...
by Patricks Dad
Thu May 30, 2019 8:33 pm
Forum: Builders' Forum
Topic: Installing Outwales
Replies: 18
Views: 1249

Re: Installing Outwales

If you want to make the inwale and outwale align, you could take some off of the inwale, outwale or both. You could also just leave it as is. Place a straight edge across the full beam to see where most of the wear will fall when you slide the canoe onto a rack to guide you. Again, leaving it alone ...
by Patricks Dad
Thu May 30, 2019 8:30 pm
Forum: Builders' Forum
Topic: Installing Outwales
Replies: 18
Views: 1249

Re: Installing Outwales

To post an image, you still need to have the image somewhere (else) where you can use the URL to reference it. Once you have the link to the picture, just use the image button (9th icon from the right above the text box you type your message in... When you click that button it will insert a string t...
by Patricks Dad
Wed May 29, 2019 6:55 am
Forum: Builders' Forum
Topic: Installing Outwales
Replies: 18
Views: 1249

Re: Installing Outwales

My first build was a Redbird with Cherry Gunwales of the dimensions noted in Canoe Craft...Ends of the gunwales were steamed and bent over a form that is somewhat more tightly curved than the sheerline itself. They were installed with only epoxy (a coat of unthickened epoxy first, wiped off and then...
by Patricks Dad
Wed May 22, 2019 2:30 pm
Forum: Builders' Forum
Topic: Attaching middle thwart with a mortise and tenon
Replies: 13
Views: 947

Re: Attaching middle thwart with a mortise and tenon

You could use Brian's Helicoil solution mounting the thwart on the bottom side of the inwale and still slide your canoe on the rack without issue.

I used these to mount my seats on a Freedom Solo a few years ago. Very clean.

And no, I'm not in on the thwart breaking contest either....
by Patricks Dad
Tue May 21, 2019 10:09 am
Forum: Builders' Forum
Topic: Attaching middle thwart with a mortise and tenon
Replies: 13
Views: 947

Re: Attaching middle thwart with a mortise and tenon

Jim, I think a bolted on Thwart might indeed be easier to replace. But consider the case where a bolted-on thwart breaks and due to its firm attachment to the gunwale, causes the gunwale itself to be damaged in the process. I think I'd rather have a thwart break clean away from the gunwale than tear...