Search found 13 matches
- Mon Oct 05, 2015 11:28 am
- Forum: Paddles, Techniques, Boat Transportation, Storage & Maintenance
- Topic: Replace damaged strips, centerline cut
- Replies: 11
- Views: 21536
Re: Replace damaged strips, centerline cut
I used a utility knife to cut across the strip, and just inside the glued joints. Then I used a chisel to remove the damaged wood. Some parts of the wood strips where splintered and separated from the inside fiberglass sheet. Most of the wood was removed was by using a chisel. I then used the utilit...
- Fri Oct 02, 2015 12:20 pm
- Forum: Paddles, Techniques, Boat Transportation, Storage & Maintenance
- Topic: Replace damaged strips, centerline cut
- Replies: 11
- Views: 21536
- Fri Oct 02, 2015 12:18 pm
- Forum: Paddles, Techniques, Boat Transportation, Storage & Maintenance
- Topic: Replace damaged strips, centerline cut
- Replies: 11
- Views: 21536
- Fri Oct 02, 2015 12:03 pm
- Forum: Paddles, Techniques, Boat Transportation, Storage & Maintenance
- Topic: Replace damaged strips, centerline cut
- Replies: 11
- Views: 21536
- Tue Jul 07, 2015 10:30 am
- Forum: Paddles, Techniques, Boat Transportation, Storage & Maintenance
- Topic: Replace damaged strips, centerline cut
- Replies: 11
- Views: 21536
Re: Replace damaged strips, centerline cut
Thank you both,
I will be cutting to fit all the pieces. I have not given S-glass much thought, but your probably correct. I think I will try that. I had always planned on removing/replacing the fiberglass on the inside after I got the outside done.
I appreciate your help.
Tim
I will be cutting to fit all the pieces. I have not given S-glass much thought, but your probably correct. I think I will try that. I had always planned on removing/replacing the fiberglass on the inside after I got the outside done.
I appreciate your help.
Tim
- Mon Jul 06, 2015 12:35 pm
- Forum: Paddles, Techniques, Boat Transportation, Storage & Maintenance
- Topic: Replace damaged strips, centerline cut
- Replies: 11
- Views: 21536
- Thu Jul 02, 2015 3:13 pm
- Forum: Paddles, Techniques, Boat Transportation, Storage & Maintenance
- Topic: Replace damaged strips, centerline cut
- Replies: 11
- Views: 21536
Replace damaged strips, centerline cut
I am replacing some damaged strips on the stern of my 15 ft Ranger. About six on both side leading up to the stem. Fiberglass and wood damaged due to boating in low water and rolling over rocks all afternoon. I removed the fiberglass and have cut out the damaged strips. I have replacement strips rou...
- Sun Jan 24, 2010 2:56 am
- Forum: Off Topic
- Topic: Canoe Camper Done
- Replies: 13
- Views: 25995
- Mon Jan 16, 2006 11:47 pm
- Forum: Builders' Forum
- Topic: First Canoe build: 15 Prospector...
- Replies: 10
- Views: 3727
Farmpunk, I finished my ranger September 05. I Worked from Bear Mountain plans and got the wood from Great Northern Craft. This was my first build. Everything seemed to go together very well. The most challenging part was after I came around the bilge. My clamps and scrap wood couldn't hold the ends...
- Mon Aug 15, 2005 3:51 pm
- Forum: Builders' Forum
- Topic: Brass Stem Band
- Replies: 2
- Views: 1529
Brass Stem Band
I have not been able to find a place that sells brass stem bands. I am building a 15 ft ranger.
Any suggestions would be appreciated
Thanks, Tim
Any suggestions would be appreciated
Thanks, Tim
- Tue Jul 05, 2005 11:23 pm
- Forum: Project Directories
- Topic: 15' 0" Prospector Ranger
- Replies: 127
- Views: 347238
Build in progress
Thanks for the welcome joatmon. I finished my forms, built the strong back and stripped up both sides and to the middle on one side. It all seems to be coming together well. I put a picture of it as my avatar. I am very happy with the results so far. Last September my dad and I spent a week in Maine...
- Tue May 10, 2005 3:07 pm
- Forum: Project Directories
- Topic: 15' 0" Prospector Ranger
- Replies: 127
- Views: 347238
thanks
Glen, thanks for answering my question.
Tim
Tim
- Tue May 10, 2005 1:38 pm
- Forum: Project Directories
- Topic: 15' 0" Prospector Ranger
- Replies: 127
- Views: 347238
Sheer lines on forms
Hi, My name is Tim O'Donnell, this is my first post and first solo canoe build. My question is regarding the sheer lines on the mold stations. On the plans these are marked on stations 6, 5, & 4, but not marked on stations 3, 2, 1, & 0. Or are the horizontal lines on the mold station drawing...