Search found 1480 matches
- Tue Jan 21, 2020 1:53 pm
- Forum: Builders' Forum
- Topic: Redbird Mold.
- Replies: 20
- Views: 15852
Re: Redbird Mold.
I do now have a recollection of having a pin through station 7 into the end of the inner stem to hold it in place. That would suggest that the stem was a bit higher than your picture suggests. Again, a detailed look at your plans should give some guidance.
- Tue Jan 21, 2020 1:25 pm
- Forum: Builders' Forum
- Topic: Redbird Mold.
- Replies: 20
- Views: 15852
Re: Redbird Mold.
Take a good look at your original plans. The top edge of the stem mold should sit below the peak of the station 7 mold a bit. I don't remember exactly how much but your picture doesn't look too far off (you note 1/4" = that seems OK - but your picture appears to be more than that which is a bit...
- Mon Jan 20, 2020 9:05 pm
- Forum: Builders' Forum
- Topic: Redbird Mold.
- Replies: 20
- Views: 15852
Re: Redbird Mold.
Looks good. It's pretty easy to glue up the inner and outer stems all in one go. Just be sure to not apply glue to the outside of the outside layer of the inner stem!
You're going to love the Redbird..
You're going to love the Redbird..
- Mon Jan 20, 2020 10:00 am
- Forum: Builders' Forum
- Topic: WRC Board Estimate
- Replies: 6
- Views: 5941
Re: WRC Board Estimate
Brian,
It seems he's starting with 23 mm thick boards. The bead and cove will take him to about 19.
It seems he's starting with 23 mm thick boards. The bead and cove will take him to about 19.
- Mon Jan 20, 2020 9:03 am
- Forum: Builders' Forum
- Topic: WRC Board Estimate
- Replies: 6
- Views: 5941
Re: WRC Board Estimate
if your boards are 150 mm wide (that's 5.9 inches)... If your strips will be .25 thick (that's a pretty common thickness) and you use a 1/16" wide blade, you should get just 18 strips per board.. Any wider blade and you won't get that many strips. Any knots or waste, and you won't get that many...
- Sun Jan 19, 2020 11:13 am
- Forum: Project Directories
- Topic: 17' 0" Freedom
- Replies: 175
- Views: 1124087
Re: 17' 0" Freedom
My 3rd Freedom 17 Carbon/Kevlar build is done. Final weight is about 39 pounds. Below is a table of my weight measures as I progressed through the build.... Component Weight Cumulative Hull 17.4 17.4 Core 3.95 21.35 Inside layer 9.5 30.85 Gunwales 2.9 33.75 Seats 1.97 35.72 Yoke 1.63 37.35 Varnish 1...
- Mon Jan 06, 2020 6:41 pm
- Forum: Project Directories
- Topic: 17' 0" Freedom
- Replies: 175
- Views: 1124087
Re: 17' 0" Freedom
I wove the seats after 3 coats of Epifanes on the frames and then added 2 more coats across the whole thing (cord and all).
- Mon Jan 06, 2020 10:10 am
- Forum: Project Directories
- Topic: 17' 0" Freedom
- Replies: 175
- Views: 1124087
Re: 17' 0" Freedom
I fabricated cleats out of carbon fiber tape and epoxy (4.5 ounces for 8 of them). https://scontent-dfw5-2.xx.fbcdn.net/v/t1.0-9/80465525_10157241990207885_4884491998788059136_n.jpg?_nc_cat=106&_nc_ohc=hvu6m9HZaaIAQlfjOqieUuPBxuCi6bKeonqJx0pxkHpmTMWFSvbX63EpA&_nc_ht=scontent-dfw5-2.xx&oh...
- Sun Jan 05, 2020 9:11 pm
- Forum: Project Directories
- Topic: 17' 0" Freedom
- Replies: 175
- Views: 1124087
Re: 17' 0" Freedom
Finished my seats over the holidays. Total weight for both Bow and Stern seats ended up at 1.65 pounds (including varnish and bolts)... https://scontent-ort2-1.xx.fbcdn.net/v/t1.0-9/81358046_10157258504062885_3687156563790790656_n.jpg?_nc_cat=100&_nc_ohc=paWUMcOdVNYAQkcL13NrVb2aCPrISukhJ_1Neuxvg...
- Fri Jan 03, 2020 10:55 am
- Forum: Boat-Building Tips & Techniques
- Topic: trimming strips to stem
- Replies: 3
- Views: 10222
Re: trimming strips to stem
Welcome to the site. The Redbird is a beautiful craft. Don't attempt to cut each strip flush with the inner stem as you build the hull. Just cut them so they are out of the way of your continued build. Only once you have the hull fully stripped, then cut them all flush with the inner stem. This will...
- Wed Jan 01, 2020 9:03 pm
- Forum: Builders' Forum
- Topic: Completed!
- Replies: 4
- Views: 3883
Re: Completed!
Congratulations! It looks great! Enjoy!
- Sat Dec 28, 2019 10:29 pm
- Forum: Off Topic
- Topic: Happy Holidays !
- Replies: 6
- Views: 14148
Re: Happy Holidays !
sadly, I just sold my Freedom Solo last weekend. I'll need to build a second one.
- Fri Dec 27, 2019 10:54 pm
- Forum: Project Directories
- Topic: 17' 0" Freedom
- Replies: 175
- Views: 1124087
Re: 17' 0" Freedom
I tried the thin blade on the angle grinder too. I think the oscillating saw works quite a bit better (and less likely to wander quickly).
- Fri Dec 27, 2019 10:49 am
- Forum: Project Directories
- Topic: 17' 0" Freedom
- Replies: 175
- Views: 1124087
Re: 17' 0" Freedom
Good question. I have tried a couple different things. I ended using one of those vibrating/oscillating tools. It cuts fairly slowly but gets the job done with a fairly smooth cut.
- Thu Dec 19, 2019 9:34 pm
- Forum: Builders' Forum
- Topic: Epoxy dried with white streaks
- Replies: 15
- Views: 14174
Re: Epoxy dried with white streaks
I'm about 20 miles NW of you