19' 9" Chaa Creek Expedition

Use the Project Directories as quick-reference tools to help you find other builders working on similar projects to yours.
Post Reply
User avatar
Cruiser
Posts: 867
Joined: Sat Apr 27, 2013 10:21 am
Location: Bowmanville, Ontario

Re: 19' 9" Chaa Creek Expedition

Post by Cruiser »

I have shifted my focus temporarily from the canoe to making a new hammock/UnderQuilt/Tarp for this season ... but I will try and get out tot he shop today and see if I can take a few pics of where I am going with the portage thwart.


Brian
User avatar
jimlgordon
Posts: 109
Joined: Mon Nov 20, 2017 6:57 pm
Location: Bainbridge Island, Washington

Re: 19' 9" Chaa Creek Expedition

Post by jimlgordon »

IMG_7288.jpg
laminated thwart experiment ... turned out quite strong and lightweight ... will be shaped more later
User avatar
jimlgordon
Posts: 109
Joined: Mon Nov 20, 2017 6:57 pm
Location: Bainbridge Island, Washington

Re: 19' 9" Chaa Creek Expedition

Post by jimlgordon »

IMG_7341.jpg
bulkhead components
User avatar
jimlgordon
Posts: 109
Joined: Mon Nov 20, 2017 6:57 pm
Location: Bainbridge Island, Washington

Re: 19' 9" Chaa Creek Expedition

Post by jimlgordon »

IMG_7310.jpg
started shaping the laminated thwart
User avatar
jimlgordon
Posts: 109
Joined: Mon Nov 20, 2017 6:57 pm
Location: Bainbridge Island, Washington

Re: 19' 9" Chaa Creek Expedition

Post by jimlgordon »

any other ideas for all wood portage yokes?
User avatar
Cruiser
Posts: 867
Joined: Sat Apr 27, 2013 10:21 am
Location: Bowmanville, Ontario

Re: 19' 9" Chaa Creek Expedition

Post by Cruiser »

I am still redoing all my camping gear and i don't have any pics of what I am planning for the current build, there has been a progression of yoke designs for my boats, I am applying everything I learned on this last one.

You may consider the following points .... they are just what I am using for the design and based on what I have learned so far ... I am using cherry trim, so assume hardwood = cherry, but truthfully most other hardwoods will be about the same
- 2 pieces of hardwood 1/2" x 3/4" is enough to support the weight of an average canoe (~40-50#s) for a yoke
- making the dish from hardwood costs a lot of weight and does not really contribute to the purpose of carrying the load of the canoe

If 2 pieces of hardwood (sized as above) were shaped (to flare at the gunnels) and were connected to a light softwood dish (say white cedar) through the center, remember the dish part only needs to slightly less than your shoulder width, it does not need to go to the gunnels .... I believe a significant amount of weight would be saved. In the process I believe a really cool looking yoke could be created. I intend to do just that for my solo, using hidden hardware to easily install and remove as required.

Brian
User avatar
jimlgordon
Posts: 109
Joined: Mon Nov 20, 2017 6:57 pm
Location: Bainbridge Island, Washington

Re: 19' 9" Chaa Creek Expedition

Post by jimlgordon »

now that is getting interesting... can you elaborate on the "dish" idea though?
User avatar
jimlgordon
Posts: 109
Joined: Mon Nov 20, 2017 6:57 pm
Location: Bainbridge Island, Washington

Re: 19' 9" Chaa Creek Expedition

Post by jimlgordon »

gluing up some more laminate components... 3 ply, 1/4 maple laminate turns out to be super strong with a slight amount of spring under a lot of pressure
Attachments
IMG_7352.jpg
User avatar
Cruiser
Posts: 867
Joined: Sat Apr 27, 2013 10:21 am
Location: Bowmanville, Ontario

Re: 19' 9" Chaa Creek Expedition

Post by Cruiser »

Hi Jim,

This is a photo of the NWC dish I made to replace the typical big foam blocks, on my solo yoke, that attaches to the seat. This dish only weighs in at a few ounces, much lighter than foam blocks or a hardwood dish.

Image

The idea is to use that sort of lightweight dish, and just put a couple of hardwood rails side to side to carry the actual load, while the dish makes for a comfy carry. The actual rails could be solid pieces or laminated 1/4" pieces, shaped to give flair and maybe please your eye for shape. You may need to go a bit thinner if you want to bend very much (or use steam at 1/4"). Anyway, I am a few days from getting back to the shop and starting mine.

Brian
Last edited by Cruiser on Fri May 04, 2018 8:45 pm, edited 1 time in total.
User avatar
Jim Dodd
Posts: 1359
Joined: Wed Feb 08, 2006 11:08 pm
Location: Iowa

Re: 19' 9" Chaa Creek Expedition

Post by Jim Dodd »

Sorry, Brian, but the pic is not coming up.
Keep your paddle wet and your seat dry!
User avatar
Cruiser
Posts: 867
Joined: Sat Apr 27, 2013 10:21 am
Location: Bowmanville, Ontario

Re: 19' 9" Chaa Creek Expedition

Post by Cruiser »

I refreshed the link, tell me if that helped Jim
User avatar
Jim Dodd
Posts: 1359
Joined: Wed Feb 08, 2006 11:08 pm
Location: Iowa

Re: 19' 9" Chaa Creek Expedition

Post by Jim Dodd »

Yes ! Thanks !

Jim
Keep your paddle wet and your seat dry!
User avatar
jimlgordon
Posts: 109
Joined: Mon Nov 20, 2017 6:57 pm
Location: Bainbridge Island, Washington

Re: 19' 9" Chaa Creek Expedition

Post by jimlgordon »

IMG_7477.jpg
more sanding and filling on the outer hull to get it nice and smooth
User avatar
jimlgordon
Posts: 109
Joined: Mon Nov 20, 2017 6:57 pm
Location: Bainbridge Island, Washington

Re: 19' 9" Chaa Creek Expedition

Post by jimlgordon »

IMG_8381small.jpg
Testing some new "clamps" for gunnels
User avatar
jimlgordon
Posts: 109
Joined: Mon Nov 20, 2017 6:57 pm
Location: Bainbridge Island, Washington

Re: 19' 9" Chaa Creek Expedition

Post by jimlgordon »

IMG_8383small.jpg
lots of new "clamps"
Post Reply