Eastern Cedar First Launch....

Welcome to the new Bear Mountain Builders Forum - an interactive internet service we provide to encourage communication between canoe and kayak builders
Post Reply
User avatar
Sherm
Posts: 73
Joined: Fri Nov 20, 2009 8:28 pm
Location: Milledgeville, Georgia

Eastern Cedar First Launch....

Post by Sherm »

Finally launched my second Hiawatha.This one made of Eastern Red Cedar.
The Eastern Cedar added about 18lbs. to the weight. This wasn't noticeable on the
water, it paddled fast and maneurvered very well.
Just wondering that our desire for "lite-weight" might be a little over rated.
I found a "blister" just under the fiberglass the same as Dawne described in her latest post. I justed cut it out , sanded and varnished. Not too concerned with it.
If there where more I think they would have showed up already. My explanation is;probably caused from a dropplet of Blood,Sweat, and/or Tear from the building process.

Image


Image


Image
Last edited by Sherm on Thu Jul 01, 2010 8:30 pm, edited 1 time in total.
Rick
Posts: 727
Joined: Thu May 27, 2004 9:23 am
Location: Bancroft, Ontario

Post by Rick »

The Eastern Cedar added about 18lbs. to the weight.
I used to burn ERC in a wood stove in eastern Ontario, it was heavy and hard enough. What was the final weight?

Good-looking canoe, BTW.
User avatar
Sherm
Posts: 73
Joined: Fri Nov 20, 2009 8:28 pm
Location: Milledgeville, Georgia

Post by Sherm »

68 or 69 lbs. I used White Oak for the Gunwales, Inwales and Decks. That was
"pretty" heavy stuff also.
willo
Posts: 156
Joined: Sun Jul 15, 2007 12:48 pm
Location: Echo Bay ON.

Post by willo »

Well you may be heavy for a strpper but your still lighter than plastic and probably even a pound or two lighter than the same boat done in fiberglass. Maybe not a tripper , but you look to have found a nice place to play. Looks nice in the water.
User avatar
Glen Smith
Posts: 3719
Joined: Sat May 08, 2004 9:08 am
Location: Baie-St-Paul, Quebec, Canada

Post by Glen Smith »

Looks fantastic, enjoy it.
User avatar
Jim Dodd
Posts: 1359
Joined: Wed Feb 08, 2006 11:08 pm
Location: Iowa

Post by Jim Dodd »

Nice job on the Hiawatha !
I remember my Hiawatha. I set it up as a tanden, but it made a much better solo !
I enjoyed mine, and I can see you're enjoying yours !
Congrats!
Jim
Keep your paddle wet and your seat dry!
User avatar
Jim Dodd
Posts: 1359
Joined: Wed Feb 08, 2006 11:08 pm
Location: Iowa

Post by Jim Dodd »

Did you build from plans in the "Canoecraft " book, and if so, was it the early edition?
Keep your paddle wet and your seat dry!
User avatar
Sherm
Posts: 73
Joined: Fri Nov 20, 2009 8:28 pm
Location: Milledgeville, Georgia

Post by Sherm »

Yes, it was from the "CanoeCraft" Book. A great read. It was the latter
edition, I think 2006. It makes a fine River Fishing Craft.
User avatar
Jim Dodd
Posts: 1359
Joined: Wed Feb 08, 2006 11:08 pm
Location: Iowa

Post by Jim Dodd »

My Hiawatha was from the earlier edition.
I always thought to add tumblehome to the design, and turn it into an AWESOME solo.
Again nice job, and enjoy !
Jim
Keep your paddle wet and your seat dry!
Post Reply