19' 9" Chaa Creek Expedition

Use the Project Directories as quick-reference tools to help you find other builders working on similar projects to yours.
Post Reply
User avatar
Cruiser
Posts: 867
Joined: Sat Apr 27, 2013 10:21 am
Location: Bowmanville, Ontario

Re: 19' 9" Chaa Creek Expedition

Post by Cruiser »

Jim,

Usually when the molds are setup, the order is
- bow/stern assemblies first
- setup the alignment string
- then start at each end and work to the center station, aligning to the string for each station

Each station will likely require some horizontal "adjustments" to make them all line up with each other ... the bottom is aligned to your strongback center mark, then the station is tilted (keeping the bottom on the mark) to make sure it also aligns at the center mark at the top.

I just did that in this thread:
viewtopic.php?f=3&t=2006&start=60

Now if you were just putting a few stations on to see what it would like , then ignore the comment ... otherwise, the initial alignment is a pretty big deal.


Brian
User avatar
jimlgordon
Posts: 109
Joined: Mon Nov 20, 2017 6:57 pm
Location: Bainbridge Island, Washington

Re: 19' 9" Chaa Creek Expedition

Post by jimlgordon »

Yeah, I set up a few so the others in the woodshop can get an idea of the space requirements. They aren't tightened down yet. Another kayak building class (Joe from Redfish Kayaks in Port Townsend) will be starting up next month so we are figuring out the space requirements. The strongback however is now all tightened up now and ready to go. I have a slot in the block where the molds attach so I can wiggle them around to adjust as needed. I got in on the kayak building class with Joe in that same woodshop. I imagine this canoe will be easier in some ways than a kayak and harder in others... bigger, more strips, and fancier, hand built seats. This will be our first time with two boats underway like this so it will be a good test.
User avatar
Jim Dodd
Posts: 1359
Joined: Wed Feb 08, 2006 11:08 pm
Location: Iowa

Re: 19' 9" Chaa Creek Expedition

Post by Jim Dodd »

Always good to do two at a time ! Let the kayak get ahead of you, and you can benefit from the mistakes !
I can't believe I said that ! :wink

Keep the pics coming !

Jim
Keep your paddle wet and your seat dry!
User avatar
jimlgordon
Posts: 109
Joined: Mon Nov 20, 2017 6:57 pm
Location: Bainbridge Island, Washington

Re: 19' 9" Chaa Creek Expedition

Post by jimlgordon »

IMG_6374 (1).jpg
Kayak class cancelled... I got the green light to proceed with the build. Started attaching and adjusting the forms. Lasers are cool.
User avatar
Cruiser
Posts: 867
Joined: Sat Apr 27, 2013 10:21 am
Location: Bowmanville, Ontario

Re: 19' 9" Chaa Creek Expedition

Post by Cruiser »

Just a little jealous .... you have better toys than I do, lol



Brian
User avatar
Patricks Dad
Posts: 1477
Joined: Wed Oct 13, 2004 1:11 pm
Location: Warrenville, Illinois

Re: 19' 9" Chaa Creek Expedition

Post by Patricks Dad »

I found the blur of the laser to be too much and the effort to align it too time-consuming. I went back to the fine string. It's easy to set up and stays put...

But yes lasers are cool...
Randy Pfeifer
(847) 341-0618
Randy.Pfeifer1@gmail.com
User avatar
jimlgordon
Posts: 109
Joined: Mon Nov 20, 2017 6:57 pm
Location: Bainbridge Island, Washington

Re: 19' 9" Chaa Creek Expedition

Post by jimlgordon »

Should I pre-glue short strips into longer ones before planking or do that while planking? Skarf joint or butt joint?
User avatar
Patricks Dad
Posts: 1477
Joined: Wed Oct 13, 2004 1:11 pm
Location: Warrenville, Illinois

Re: 19' 9" Chaa Creek Expedition

Post by Patricks Dad »

Butt joints on the fly. Some builders build up their strips on the bench using scarf joints. Others don't. Do what feels right to you.
Randy Pfeifer
(847) 341-0618
Randy.Pfeifer1@gmail.com
User avatar
Cruiser
Posts: 867
Joined: Sat Apr 27, 2013 10:21 am
Location: Bowmanville, Ontario

Re: 19' 9" Chaa Creek Expedition

Post by Cruiser »

Either way works ... pick what will work best for you .... I would check the forums here for tips/tricks on doing what you pick. I suspect butt joints on the boat will be easiest, in which case you will want a few small strips pieces covered in tape to act as a splint (spring clamp in place) when you make them.

If I know I am going to have short lumber and a lot of joints to do ... my preference is to skarf the source lumber into suitable lengths. This allows me to control/stagger where the joints occur and I am only doing a few joints instead of many individual ones.


Brian
User avatar
Jim Dodd
Posts: 1359
Joined: Wed Feb 08, 2006 11:08 pm
Location: Iowa

Re: 19' 9" Chaa Creek Expedition

Post by Jim Dodd »

I glue up splices right on the canoe. Preferably between the forms, and at places that doesn't stress the strip.
The bead and cove is a great aid in holding strips in place !
A pic of how I do it.
I like to use the bigger 2" spring clamp, that way I can continue with my next course of strips.

Image

Be sure to cover the little clamping blocks with tape !

Jim

PS ! I prefer Fish line for setting my forms. To me it's more precise, but a lazer is fine !
Last edited by Jim Dodd on Sat Dec 30, 2017 5:24 pm, edited 1 time in total.
Keep your paddle wet and your seat dry!
User avatar
Jim Dodd
Posts: 1359
Joined: Wed Feb 08, 2006 11:08 pm
Location: Iowa

Re: 19' 9" Chaa Creek Expedition

Post by Jim Dodd »

While you are prepping to strip, I'll pass on some pics, that might help as you go .
If you plan to use staples. adding several layers of tape to the bottom of your stapler, will prevent bruising of the wood, by sinking the staples too far in. Also makes it a lot easier to remove the staples !

Image

When fitting strips, a light on the strongback helps to see where the strips need trimming.

Image

I like to tape my center form a different color, as I always start stripping from the center out. Also I make a mitre box, that sits between the forms, for squaring up splice joints, right on the forms.

Image

I like to fasten my forms to the cleats on the strongback with C-clamps. This makes it super easy to adjust the forms, during set up. They provide a clamping surface to persuade strips that don't want to stay tight to the forms. Also a handing holding place for my glue bottle. I love a small pencil shaped tip on the glue bottle.

Image

Image

For squeezing glue out of the bottle, I enlist the help of a 2" spring clamp ! It saves these Old hands a lot of suffering !

Image

My favorite staple pulling tool. Available at some online Office supply stores. Fairly inexpensive, and a great tool ! Order two, incase you can get a helper !

Image

Last but not least ! I staple two temporary strips to the stem forms, one, sometimes two on each, to check vertical stem alignment.
I leave these on, until I'm at least half way up the sides, with strips. Or until they are in my way !

Image

Thats a few tips, I hope will help during the stripping process !

Good Luck !

Jim
Keep your paddle wet and your seat dry!
User avatar
jimlgordon
Posts: 109
Joined: Mon Nov 20, 2017 6:57 pm
Location: Bainbridge Island, Washington

Re: 19' 9" Chaa Creek Expedition

Post by jimlgordon »

IMG_6382.jpg
IMG_6386.jpg
They were a little uneven so I planed them slightly... just shaved a little off and knocked off some high spots.
User avatar
jimlgordon
Posts: 109
Joined: Mon Nov 20, 2017 6:57 pm
Location: Bainbridge Island, Washington

Re: 19' 9" Chaa Creek Expedition

Post by jimlgordon »

IMG_6782 (1).jpg
The molds are ready for planks now.
User avatar
Jim Dodd
Posts: 1359
Joined: Wed Feb 08, 2006 11:08 pm
Location: Iowa

Re: 19' 9" Chaa Creek Expedition

Post by Jim Dodd »

Looks Great !
Now for the fun part ! I love seeing a hull take shape as it's stripped. The anticipation level rises with every strip !

Jim
Keep your paddle wet and your seat dry!
User avatar
jimlgordon
Posts: 109
Joined: Mon Nov 20, 2017 6:57 pm
Location: Bainbridge Island, Washington

Re: 19' 9" Chaa Creek Expedition

Post by jimlgordon »

IMG_6796 (1).jpg
setting up mill the cove and bead on the mountain of strips
Post Reply